
Dụng Cụ Tiện Ích
Puck Quadlock có cơ cấu khóa (-ĐANG HOÀN THIỆN-)
Remix of Ngàm Quadlock (Cơ chế Khóa) By jsinkers_917712
- Downloads
- 179
- Likes
- 24
- Views
- 1,734
- Remixes
- 0
- Comments
- 0
Files 11 5.4 MB
- Quadlock_Mech_V4_1777110571.3mf3MF · 88.6 KB
- V3_part_1_quadlock_puck_1777110572.stlSTL · 88.9 KB
- V3_part_2_quadlock_puck_lock_1777110573.stlSTL · 91.7 KB
- V3_part_3_quadlock_puck_lid_1777110574.stlSTL · 45.4 KB
Make a variant with AI
Build another version of this model.
Details
- Model ID
- #337727
- Category
- Dụng Cụ Tiện Ích
- Published
- License
- Creative Commons — Attribution
Description
Infos:
tolerances between parts: 0,2mm
Insert the magnets at the right position and orientation so they pull each other
used magnets (5x2mm) since V3: https://www.amazon.de/gp/product/B07T13H3R5/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
Changelog 03.05.2024
- added version 4
- older versions are still online
- changed main format to .3mf (every part is now in one file only)
- printfiles comming soon
- new version:
- redesigned to let the mechanism slide on from the bottom → changed the magnet orientation (magnet size stays the same)
- removed lid (now one piece with the quadlock puck)
- advised to print the parts like shown in the foto and with supports only on printbed ( !! avoid tree support !! )
- part variation similar to previous versions:
- part 1 (green)
- quadlock puck
- part 2 (yellow)
- lock mechanism
- part 1 (green)
- future ideas:
- a twist in lock mech to change the magnet orientation back to normal
because now the magnets dont hold together that good and i dont like the mushy feeling when unlocking
- a twist in lock mech to change the magnet orientation back to normal
Changelog 19.04.2024
- added version 3
- older versions were renamed:
- V1: first version which didn't acually function
- V2: new name for V1.5 (old v11 ending)
- older versions were renamed:
- new version:
- part variation is the same as in V2:
- part 1 (green)
- quadlock puck
- part 2 (yellow)
- lock mechanism
- part 3 (red)
- lid to keep the other 2 parts together
- part 1 (green)
- changed the magnetsize to 5x1 mm magnets
- reason: to get smaller
- in one hole there are two magnets
- in total you need 16 magnets for one puck
- amazon link: https://www.amazon.de/gp/product/B07T13H3R5/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
- old lid is compatible with new version
- part variation is the same as in V2:
- added printfiles
- Infill: 5%
- 0,3mm layerheight
- speed is cranked up a little bit
- Material: PLA
- nozzle: 215-200°C
- bed: 70°C
- roadmap:
- adding slide mechanism to twist the lid into the puck
Changelog 13.04.2024
- added version 1.5
- old version left online to check out the differences
- new version has 3 parts
- Teil_1 (green)
- quadlock puck
- Teil_2 (yellow)
- lock mechanism
- Teil_3 (red)
- lid to keep the other 2 parts together
- Teil_1 (green)
- added recommended print orientation in the photos
- Fusion file follows with the final version (if this one aint it)
Print spec
- Formats
- 3mfgcodestl
- Model files
- 11
- Total size
- 5.4 MB
- Largest file
- 1.5 MB
0 comments
You may also like 12 models
See all-

-

-
New -

-

-

-

-

-

-
New -
New -


