
Bộ căng dây đai cho máy in 3D Elegoo Neptune 3 Pro
- Downloads
- 520
- Likes
- 75
- Views
- 3,128
- Remixes
- 0
- Comments
- 16
Files 6 12.5 MB
- belt_tensioner-stock_1766272759.stlSTL · 2.8 MB
- x_axis_belt_tensioner_housing-stock_1766272760.stlSTL · 2.1 MB
- neptune3pro_belt_idler_carrier_v6_1766272761.stlSTL · 268.5 KB
- neptune3pro_x-axis_belt_tensioner_open_housing_1766272762.stlSTL · 238.3 KB
Make a variant with AI
Build another version of this model.
Details
- Model ID
- #33003
- Category
- Máy In 3D
- Published
Description
I did not like the stretchy generic GT2 belts that came with the Neptune 3 Pro, so I set out to replace them with genuine Gates GT2 belts. Since I was going to have everything apart, I decided to upgrade the stock idlers to proper toothed idlers (also Gates brand from Filastruder). I don't think that the idlers themselves make any appreciable difference in the print quality, but I just like to tinker and “do things right”, so…
The stock idlers use a 4mm shaft, whereas the standard toothed idlers take a 5mm shaft (or 3mm for Prusa style), so we need a larger hole for the shaft in the tensioner itself. I also found that with the replacements I sourced I needed a little extra clearance in the x-axis belt tensioner housing. Additionally, I modeled openings into the housing - mostly so that you can admire your handiwork, although you may also be able to just get the belt in and out without removing the housing depending on how you've crimped your belt.
Notes:
- The x-axis belt tensioner housing will likely need to be replaced as noted above. However, the y-axis housing has plenty of room to accept the modified tensioner.
- I found that I needed to sand down the diameter of the binding bolts to get a snug slip fit in the new idlers. YMMV.
- I found that I had to grind down the top of the binding bolt head to clear the actual x-axis gantry since there's no slot in the front face of the extrusion used by Elegoo.
- I used some shims to give the bearings a little clearance inside the tensioner. This probably isn't really necessary given the “sloppy" nature of these assemblies, but I've included a link to the parts anyway.
- You need a short M3 threaded insert in the tensioner to accept the M3 socket cap screw that the tensioner knob runs on. Reuse the original screw and knob and put a little thread locking compound on the screw when you seat it down into the insert.
- Since you have everything disassembled, it's probably best to go ahead and replace the pulleys at the same time as the belts and idlers since they're cheap and then everything is guaranteed to match up.
- The parts I used:
- Gates 2GT Idler - Filastruder
- Gates 2GT Pulley - 6mm, 20 Tooth - Filastruder
- Gates 2GT Belts - Filastruder
- 316 Stainless Steel Binding Barrel, 316 Stainless Steel Binding Barrel, M4 Thread Size, 16 mm Long | McMaster-Carr
- M4x12mm Socket Cap Screw
- Original CNC Kitchen Gewindeeinsatz / threaded insert SET Short 200 Stk / pcs – CNCKitchen
- 1074-1095 Spring Steel Shims, for Shortening 5mm Diameter Screw Shoulder, 0.01" Thick | McMaster-Carr
Printing Parameters:
- Printed in PLA
- 0.2mm layer height
- I printed the tensioner on end without supports. The shaft holes will get a little squished even with supports and need to be drilled out, so I just don't worry about it.
- Print the housing on its front face with tree supports.
Finally, I've included Fusion 360 files for the modified parts as well as STLs for the stock belt tensioner and x-axis housing for reference.
Print spec
- Formats
- f3dstl
- Model files
- 6
- Total size
- 12.5 MB
- Largest file
- 6.5 MB
16 comments
You may also like 12 models
See all-

-

-
New -

-

-

-

-

-

-

-

-


