Skip to main content
F3D
Fall is looming !! The weaving loom – Khung cửi dệt để bàn 1

14 images

Large file collection DIY

Fall is looming !! The weaving loom – Khung cửi dệt để bàn

By TheRookie_2844114

Downloads
1,928
Likes
1,405
Views
23,096

Files 46 87 MB

  • Base_-_Tether_line_6x_1767494295.stlSTL · 65.1 KB
  • Base_-_Tether_for_thread_6x_1767494296.stlSTL · 1 MB
  • Base_-_Roll_over_beam_2x_1767494297.stlSTL · 56.3 KB
  • Base_-_Left_Panel_1x_1767494297.stlSTL · 7 MB

Make a variant with AI

Build another version of this model.

Open Studio

Description

DONT forget to vote for the Printables Award 2025 if you like this model !!!! Its free and you could win a printer too by voting !!!

Im in 2 categories with this model and it would be much appreciated thank you !!

I hope lots of people will have fun with this machine because i sure did haha 

For the base if your printer bed is not big enough (like mine) I have cut both side panels in the slicer with a dovetail at 20 degree. See picture

  1. 4 Walls 

  2. 20% infill

  3. Lever Housing need to be printed on the side like an L

  4. Big beams is labeled on the side it needs to be printed

  5. Number of individual parts to print is wrote on each parts title

  6. Both shafts need to be insert before bolting it to the Base 

  7. you can either use filament or nylon threads to tie the pull bar to the tethers

Needed to complete the build:  

  1. M4 heated insert 30 total

  2. M4 bolts 12mm for the base x20

  3. M4 bolts 12mm for the gentry x10

  4. 2kg of pla (with left over in case of failure)

  5. As a retainer for the pulley pin use a short piece of 1.75mm PLA or PETG filament as a cutter pin and fold both end to secure

  6. No support needed ! 

  7. Brim needed for pins and beams ! 

  8. Small elastric band for hair or to make bracelet x2 for the locks

  9. A nice pair of pliers for the Lever housing supports (tight fited supports)

  10. Some Nylon or Polyester threads for the gantry shafts 

I like a tight fit (who doesnt) so you might need to sand down the edges of brimed parts

For the cables use big Nylon or polyester thread no elastic threads. Cut a long piece - fold it to equal parts, make a loop and pass it through the back of the lever hole and then over to lock it in place. Push both threads between the roller pin on top and than one on each side. Next is over the pulley and down. Tie a tight knot on the shaft eye below.

HAVE FUN AND SEND PICS PLS !!!

Edit : 

  1. I have resized the pull bar since it was 20mm shorter for some reason sry my bad and added a picture for the retainer pin filament

  2. Sorry again both shafts+arch+post were a bit too tight so I have ajusted them (I thought i'd checked everything before posting I guess i am human lol)

  3. Pre-cut for the panels added (for smaller printers) Tested

  4. Pre-cut for all the cylindrical beams (for smaller printers) Not tested at your own risk :P

  5. Resized beam cap insert

  6. Pre-cut beam + Support couldnt not be done in the slicer so I did it in software.

  7. Updated Post for more support for the shafts

  8. Adding a Tether anker so you can use nylon thread to link the Beam to the pull bar. You can print either one im just giving you options

  9. Added photos of exploded view and Inserts Location to help for assembly.

  10. Thin down lock and sleeve so it is easier for M4 x 12mm it was a bit tight.

  11. Video updated more detailed !!! next will be a video of how to set it up

  12. Added 2 *.zip files for glued option instead of inserts (not tested - print at your own risk - waiting on test version)

Here is the video for assembly : 

Here is a video to help you thread the machine :

Version Française :

Read more Show less

Print spec

Formats
3mfstlzip
Model files
46
Total size
87 MB
Largest file
20.5 MB

0 comments

See all