Skip to main content
F3D
Hộp đựng TS101 Cứng cáp (Phiên bản Nam châm) 1

3 images

DIY

Hộp đựng TS101 Cứng cáp (Phiên bản Nam châm)

Remix of Hộp Đa Phần Vỏ Pinecil/TS100/TS80 Chắc Chắn (V2) By PjotrStrog

By FrostyTheClow_484507

Downloads
1,431
Likes
382
Views
9,580
Remixes
1

Files 4 90.9 MB

  • TS101_Box_1766686592.stepSTEP · 8.8 MB
  • TS101_Box_1766686593.3mf3MF · 16.9 MB
  • TS101_Box_1766686595.stlSTL · 59.3 MB
  • TS101_Box_-_Magnetic_Desolder_Braid_Holder_1766686599.3mf3MF · 5.9 MB

Make a variant with AI

Build another version of this model.

Open Studio

Remix versions 1

See all 1 remix

Description

After using the very nice TS100 box from @pjotrstrog I decided to make a few small improvements according to my own needs. The inserts will fit into the original box as I didn't want to reprint the main box.

Here are the changes I've made:

  • There is now a lid to cover the tip cleaning tray to prevent the solder balls from getting into the rest of the case when it's stowed (held in place with magnets).
  • I've added holders in the lid for 3 tips, I've also made it easier to remove the tips from the case.
    • There is still enough room under the tips in the lid to store two small bags of heat shrink tubing.
  • Solder spools:
    • The solder spools are held in place magnetically instead of with a clip as I prefer to hold the spool in my left hand when soldering. This makes them easier to remove & stow.
    • I removed the solder guide loop as I never used it.
    • The spools now hold more solder.
    • There is an internal loop to make winding easier.
    • I've added notches to the top to make stowing easier.
    • Walls are thicker so everything is more rigid and they hold together better.
  • I've added two small desoldering wick holders so that it is easier now to get at my 1mm & 2.5mm wicks.
  • The iron stand is now held in place magnetically when stowed, this is easier to remove and less likely to fall out when being transported.
  • The screw for the stand is self tapping.
    • I've not tested this as I didn't want to re-print it and waste filament. However, I used the same measurements I've used on many other models to achieve this.
  • I've added two small 4mm screw driver bodies with magnetic retainers. These are for the tip stabilising & earth screws on the iron itself. You will need some 4mm hex bits for these bodies.
  • I've added a TS101 label to the lid, if you don't want the box labeled just print it in one colour.

You will need the following hardware to make this:

  • 6x M3x20 screws
  • 1x 608 bearing.
  • 4x 5x1mm round neodymium magnets
  • 10x 4x2mm round neodymium magnets
  • 2 6x3mm round neodymium magnets
  • 1x 8x1.5mm round neodymium magnets
  • 4mm hex bit - Hex 1.5mm
  • 4mm hex bit - Flat 3mm

I've tried to make all of the magnets a friction fit but you may need to epoxy some into place. I needed to epoxy the 6mm & 8mm magnets.

I strongly recommend printing the soldering stand in PETG or some other high temperature filament, I suspect PLA will sag.

The models I've uploaded have 2 very small changes from the model I printed:

  1. I've shortened the retaining posts for the solder spools so that the magnets are easier to install and the spools are easier to stow/unstow.
  2. I've moved the 8mm magnet by a few mm so that it holds the 608 bearing a little further from the solder spools.

I've included a STEP file for anyone wanting to make their own modifications.

Read more Show less

Print spec

Formats
3mfstepstl
Model files
4
Total size
90.9 MB
Largest file
59.3 MB

0 comments

See all