Skip to main content
F3D
Dụng cụ Cắt Chai Nhôm Slider 1

5 images

Máy In 3D

Dụng cụ Cắt Chai Nhôm Slider

By Ptitloup3DLAB

Downloads
57
Likes
8
Views
549

Files 8 5 MB

  • Slider_Cutter_-_07mm_1767917973.stlSTL · 718.3 KB
  • Slider_Cutter_-_08mm_1767917974.stlSTL · 580.5 KB
  • Slider_Cutter_-_09mm_1767917975.stlSTL · 569.1 KB
  • Slider_Cutter_-_10mm_1767917976.stlSTL · 671.4 KB

Make a variant with AI

Build another version of this model.

Open Studio

Description

Durable Pet bottle cutter.

I was using the very good design from @3denvangelist, you can find it there : https://www.printables.com/fr/model/299493-community-bottle-cutter-the-ricardo-pereira-mod-v3

The @3denvangelist design is way better than all designs you can find on this website and works huge great, rapid change between dimensions and cut fine. 

My problem is that im a pretty big maker, i make near 50 bottles on 1 cession and the upper part is cutted by the bottle even with coins after 20/30 bottles. So i have to print again parts. 

I search how to improve the design and began to cut in 2 his design and added a plate made of an old cool-plate bambu lab. It works but was a bit hard to setup.

So i decided to try making my own design in same idea than up but this time with an aluminium slider. i was really new in design on Fusion 360 so its been a long way to what i propose to you today.

I made the design as we can reprint 1 part if needed and not to be forced to print all. This is why the design is in 4 parts + the plate + template.

You just have to slide the cutter into plate guides, no clips no screw.

As i was using the design of @3denvangelist i made the holes of the plate at same place avoiding me making new holes in my table.

TAKE CARE of the fact that there are 2 templates, 1 for 7mm belt and 1 for 8 to12mm belt.

The reason is as the bearings 608 makes 7 mm high, and that the bottle you have to cut with this 7mm makes a lot of force and the result was bad.

So i made a special implantation of the 2 bearings for the 7mm, They are less distant from each others. Like that, it works fine.

As the bearing makes 7mm and we want to cut 7mm and that we need a center support for the bearing, you will have to grind step by step after testing the left bearing, and when you arrive to 7mm belt you stop grind.

If you want to make all dimensions, you will need by dimension :

  • 1 x aluminium plate thickness 2mm x 40mm larg
  • 2 x bearings 608 ZZ or 2RS depend what you have.
    For info, i got black and red bearings, strangely, they are differents and black are best (for me)
  • 2 x M8 nuts.
  • 2 x M8 x 30mm screws.
  • 4 x wood screws 3.5x20 (for left upper part).
  • 4 x wood screws 3.5x25 (for right upper part).
  • 4 x wood screws on the dimension you want to fix the plate on a table if needed (what i did).
  • 1 x 8mm rod to hundle the bottle on the plate.

You will have to print the template to know where to do holes and center them on aluminium slider. These templates got the good dimensions, so you can also use it to long cut.

Here are my settings for prints, but you can do your own ones ofc :

  • PEI textured plate for me cause i got some issues with others but this is only my lowskill problem.
  • Plate with ABS with 25% infill - rim to avoid warping - 4 walls - 4 upper and 4 lower shells
  • other parts with PLA (for me PLA metal from bambu) with 20% infill- 4 walls - 4 upper and 4 lower shells - No rim and works fine
  • Pay attention for the right upper parts you have to print in vertical with normal supports, i got the best results in that way BUT you can try another side.

Well i think i didn't forget anything, if so, dont hesitate to send me a message if you have a doubt or information needed.

I want to apologise on my poor english, i tryed my best 

I wanted to wait to have make a lot of bottle to be sure that it works fine. I have cut near 100 bottles on each dimensions and it works just fine, nothing to prrint again, all parts are in good conditions.

I dont say it is the best cutter but if you need something durable, you need this one.

If you don't have aluminium plate or anything else use this one https://www.printables.com/fr/model/299493-community-bottle-cutter-the-ricardo-pereira-mod-v3

A like - A comment and feedback is totally free for you and appreciate to go on and improve myself and follow in the right direction.

Read more Show less

Print spec

Formats
stl
Model files
8
Total size
5 MB
Largest file
969.9 KB

0 comments

See all