Skip to main content
F3D
~1/4 Scale Type 1 ACA Allertor 1

12 images

Large file collection DIY

~1/4 Scale Type 1 ACA Allertor

By haroldhihat

Downloads
197

Files 29 58.8 MB

  • 10-12 Rotor.stlSTL · 3.8 MB
  • 10-12 Stator.stlSTL · 2.6 MB
  • 9-12 Rotor.stlSTL · 3.6 MB
  • 9-12 Stator.stlSTL · 2.1 MB

Make a variant with AI

Build another version of this model.

Open Studio

Description

⚠(DISCLAIMER)⚠ MY MODELS ARE PUBLISHED UNDER THE CC BY-NC-SA 4.0 LICENSE: https://creativecommons.org/licenses/by-nc-sa/4.0/

You are welcome to download, print, share, and remix all my designs with credit, butyou may not sell any of my files, prints, or remixes to make a profit. Please respect the time and effort I put into all of my designs and if I will take action against them being sold for profit. Thank you!


Bit of a smaller overall file release but here it is!! I'm super happy with how this turned out and I gained a lot of interest in the Type 1 itself while working on this project :)

PARTS LIST:

MOTOR: https://www.amazon.com/CHANCS-Electric-555-8000RPM-Accessory/dp/B0CW61NGF4/ref

SHAFT COUPLER(S):https://www.amazon.com/12Pcs-3-17mm-Coupling-Connector-Airplane/dp/B0DKT5T64L/ref

ALAN WRENCH:

Any LONG 1.5mm alan wrench will work but the ones that come with the coupler are not long enough. Here's one you can use although feel free to search for another one or style you prefer!

https://www.amazon.com/Dynamite-DYN2814-Hex-Driver-1-5mm/dp/B000BQ1SFE/ref

SLIP RING:https://www.amazon.com/Comidox-CIRCUITSx2A-Capsule-Electrical-Equipment/dp/B07H2SRMXP/ref

BEARINGS:https://a.co/d/45fWKgO

GEARBOX:https://www.amazon.com/SparkFun-Hobby-Gearmotor-140-Pair/dp/B07JX7MHSL/ref

OR: https://www.amazon.com/Pack-Dual-Shaft-Gear-Motor/dp/B0C448W34R/ref

M3 THREADED INSERTS:https://www.amazon.com/dp/B08BCRZZS3?ref

M2 THREADED INSERTS:https://www.amazon.com/ruthex-Threaded-Insert-pieces-ultrasound/dp/B088QJG676/ref

M3 HARDWARE KIT:https://www.amazon.com/Machine-Assorted-Assortment-Stainless-Threaded/dp/B0DFWYBJJJ/

M2 HARDWARE KIT:https://www.amazon.com/Machine-Assorted-Stainless-Assortment-Threaded/dp/B0DFWXRM21/ref

SMALL RUBBER BAND (Get from anywhere)

POWER:

POWER SUPPLY:https://www.amazon.com/Adapter-100-240V-50-60Hz-Converter-Transformer/dp/B0D7GGGM6Q/ref

SPEED CONTROLLER:https://www.amazon.com/RioRandTM-Upgraded-6V-90V-Motor-Controller/dp/B00F839VNQ/ref

For assembly instructions, just look at the printables for the Penetrators and type 3 Allertor. It's all the exact same in terms of assembly.

(NEW ADDITION) Although everything is mainly the same, there is a different setup you can do for the rotators. On early type 1's, the whole sound-producing front of the siren sits foreward on the rotator which leaves a big gap between the base of the horn and the rotator frame. On later Allertors, (which you commonly see on 8/12 Allertors), the horns are pushed back to be flush with the frame. I'll add an image below to show exactly what this means but which ever rotator you choose, make sure to download the corresponding parts for it!

However there are a few differences and the first is in the pulley system. For that, you'll want to press one end of a shaft coupler into the large hole and thread a long M3 bolt through the sleeve and the coupler to lock them together. Then just use the setscrew on the other side of the coupler to attach it to the motor and line up the positions with the other pulley on the gearbox motor! (Don't mind the extra M3 bolt, that was just for me to get the pulley sizes right)

There's also the addition of the Bottom Outer Rotator Plate which goes underneath the bottom of the rotator cover with the small lip side facing up into the rotator cover. Make sure to also add silicone grease to the rotator tubes and the bottom where all the weight sits or the plastic will slowly eat out over time

The horn is also attached with M2 bolts through inserts on the motor cover back (yes those holes are for M2 inserts!)

The horn IS compatible so if you'd like to make a type 1 with the type 3's horn, you can do so! (mini Waldorf would be epic!)

And for mounts and stands, also check the type 3 allertor printables

Read more Show less

Print spec

Formats
stl
Model files
29
Total size
58.8 MB
Largest file
12.3 MB

0 comments

See all