
Fraks Flexarm - Cánh tay hỗ trợ lắp Heatset Insert
- Downloads
- 416
- Likes
- 260
- Views
- 4,318
- Remixes
- 3
- Comments
- 0
Files 24 14.5 MB
- BHCS_Center_Bracket_1773544754.stlSTL · 1 MB
- a-Washer_W-Magnet_Joint-x2_1773544756.stlSTL · 582.6 KB
- a_Short_Spring_Retainer-x4_1773544758.stlSTL · 351.4 KB
- a_Long_Spring_Retainer-x4_1773544760.stlSTL · 305.8 KB
Make a variant with AI
Build another version of this model.
Remix versions 3
Giá đỡ FRAKS cho mỏ hàn FNIRSI HS-02ABytoaster_1281099 · 04/09/2026
Đế gắn mỏ hàn đa năng FRAKS có lỗ nhấn nútByArminAnderso_2466484 · 03/20/2026
Đế giữ linh kiện đa năng cho Flexarm không cần GridfinityBywikallen_322863 · 03/15/2026
Details
- Model ID
- #250913
- Category
- DIY
- Published
Description
The Fraks Flexarm is a tool-balancing arm designed to keep the attached tool parallel throughout its movement. It was created to hold soldering irons to install heat set inserts into 3D printed parts.
It has a large working area for its size, and has quick release tool holders that are held in place with magnets.
Thanks to Zack Freedman for making Gridfinity an open source project, I have included Gridfinity storage into the base. You can read more about Gridfinity at https://gridfinity.xyz/
What do I need?
- You will also need either pocket screws or a wood working fence clamp to secure the base to your work surface.
- 4 pieces of 1515 extrusion, all cut to the same length and tapped on either end. I have tested this with 200mm and 270mm lengths.
- 10x1x60mm extension springs, these seem to work well for 200-300mm builds. You can adjust the tension rate by moving the spring posts along the 1515 extrusion.
- 10x100mm dowel pin and a 10x14x30mm brass Bushing
- M10 washer, a 25mm diameter is listed, but any diameter and thickness washer will work.
- M5x30 FHCS are recommended, but BHCS are also supported. The springs will touch button heads slightly, but will not affect performance from testing.
- You will need a Soldering iron with a heatset insert adapter. I personally recommend either the Pinecil or TS101 Soldering Irons along with the adapter set from CNC Kitchen.
BOM:
Part Description
Quantity
1515 Extrusion 200-300mm (All the same length)
4
10mm OD x 1mm Wire Gauge x 60mm Long Extension Springs
4
10mm x 100mm long Pin
1
10mm ID x 14mm OD x 30mm Length Brass Bushing
1
10mmx24mm Washer
1
M3x8 FHCS
16
M3x8 SHCS
10
M3x10 SHCS
4
M3x12 BHCS
4
M3x20 BHCS
4
M5x30 FHCS (Or BHCS)
8
M3 Heatset Inserts
10
M3 Hex Nuts
20
M5 Washers/Shims (10x1)
16
6x3 Magnets
6
6x2 Magnets (For Gridfinity Base)
12
1-1/4 #8 Pocket screws (For screwing base to table)
4
Table Saw Fence Clamp (For clamping to table)
1
Print Settings
0.2mm layer heights
0.4mm Line Width
4-5 walls
4-5 top and bottom layers
40% infill
ABS and ASA have been tested
More info can be found on my github https://github.com/TurtleCrawler/Fraks_Flexarm
Print spec
- Formats
- stl
- Model files
- 24
- Total size
- 14.5 MB
- Largest file
- 1.4 MB
0 comments
You may also like 12 models
See all-

-

-

-

-
New -

-
New -

-

-
New -

-
New

