
PiBM PS/2 Model 25 Tái Hiện Máy Tính Cũ
- Downloads
- 162
- Likes
- 49
- Views
- 1,991
- Remixes
- 1
- Comments
- 0
Files 56 10.5 MB
- Electronics_Panel_-_Tiny_Llama_1766005842.stlSTL · 772 KB
- Rear_Panel_-_Tiny_Llama_1766005843.stlSTL · 172.6 KB
- OLED_Retaining_Clip_1766005844.stlSTL · 37.2 KB
- Front_Panel_1766005845.stlSTL · 357.6 KB
Make a variant with AI
Build another version of this model.
Remix versions 1
See all 1 remixDetails
- Model ID
- #111577
- Category
- Dụng Cụ Tiện Ích
- Published
Description
Detailed printing and assembly instructions on Instructables
- Update 1/3/2023.
- Alignment groove between pieces enlarged
- Display Front pieces realigned to face downward to bed. This requires a bit of support but keeps the front lip uniform with less need for putty/sanding.
- Update 1/19/2023
- Added Audio Jack connection PCB gerber file. This simplifies the audio wiring.
- Update 5/23/2023
- Add Audio Knob mounts which can harness a 6mm potentiometer, as well as an extended audio knob
Filaments used
Electronics and Hardware
Items with asterisks * have dimensions expected to fit
- 10.4 inch 1024x768 Brightness 500nits IPS LCD Screen *
- Ask seller for 50cm keyboard cable, the standard 30cm won't quite reach the rear panel
- MEISHILE 12V 10A 120W DC Switching Power supply *
- Raspberry Pi 4b *
- ...and storage card
- Icstation TPA3116D2 *
- Micro SD to SD Card Extension Cable Adapter *
- after three attempts with different models, this never operated as expected - too much electronics noise?
- Alternatively, use this Right Angle USB C Extension Cable with the alternate diskette mount.
- SWITCH ROCKER DPST 10A 125V *
- CONN JACK STEREO 3.5MM R/A *
- Speakers (2) *
- 64.3mm diameter speaker mounts - Dayton Audio DMA58-4 2" Driver
- 73.5mm diameter speaker mounts - Dayton Audio PC68-4 2-½" Driver
- Power Cord Inlet Socket *
- 3MM LED - Green
- 150ohm+ resistors for the LEDs
- Hook up wire
- Power Cable - 14 AWG
- Spade Terminals, Fork Terminals, Dupont Connectors
- Heat Shrink Tubing
- 60mm Fan
- Spring, 8mm diameter, 18 length
- USB C Type-C Male Plug Cable
- 5.5mm DC Pigtail
- 3.5mm Headphone Pigtail
- Micro HDMI to HDMI
- Prototype circuit board
- JST-XHP Connectors
- Threaded Inserts and Bolts
Finishing Supplies
- Super Glue
- Glazing & Spot Putty
- Sand Paper - 100, 400, 1000
- Primer
- Case Spray Paint
- Bezel Spray Paint
- Electronic Board Paint
- Acrylic Paint for Details
- Spray Lacquer
Tools
- 3D Printer
- I used a somewhat upgraded Ender 3 - it has OctoPrint/Raspberry Pi with camera, a PEI bed surface, dual gear extruder, and the 3D printer enclosure I had designed. However, a well tuned stock Ender 3 will be able to print all of the pieces just fine. (Unless the plastic extruder breaks!)
- Clamps for gluing, a bunch of them in various sizes
- Precision screw drivers and Hex screw drivers
- Precision tweezers
- Wire Stripper
- Cable crimper
- Terminal Crimper
- Soldering iron and solder
- Soldering stand/clamp
- Heat gun
Also, this angled fan duct can be used for airflow directed at the board.
Printing Notes - Make sure to have good bed adhesion and leveling, especially the larger pieces.
Part
Finishing
Bezel Front Icons
Glue, Putty, Sand edges
Bezel PiBM Logo
Carefully trim any excess plastic, sand surrounding surface, paint dark grey and use white/silver stamp ink for the letters
Bezel Lower Right
Support needed for the LED mount and Icons
Case pieces
Support needed for lip and grooves on the edges.
Case Rear Panel Handle
Attach this with glue to the panel
Stand Leg
Print two of these, print/paint dark grey
Front Panel
Support required for diskette bay overhang. Block out threaded mount holes.
Diskette Mount
Requires support for the bolt holes, set to 54 degrees and no extra will be printed. Print in black.
Electronics Board
Support only needed for the larger slots, unless you're confident about bridging. Block out threaded mount holes and video control icons. Print/paint dark grey.
Extra Knob Mount
Print in black
60mm Fan Cover
Print in black
Bezel Assembly
Glue, Putty, Sand surface smooth, Prime, Paint Grey-Brown
Case/Display Assembly
Glue, Putty, Sand surface smooth, Prime, Paint Antique White
Inserts and Bolts
Piece
Count
Inserts
Bolts
Bezel and display
4
M3×6mm
M3×8mm
LCD Panel and Bezel mount
4
M2×6mm
M2×6mm
LCD Control Board mount
3
M2×6mm
M2×6mm
Electronics Panel Mount
1
M3×6mm
M3×6mm
Diskette Bay Mount
2
M2×6mm
M2×6mm
Audio Board Mount
2
M2×4mm
M2×6mm
Extra Knob Mount
1
M2×6mm
M2×6mm
Power Switch Holder
2
M2×4mm
M2×6mm
Rasp Pi Mount
4
M2×6mm
M2×6mm
Buck Converter Mount
2
M2×6mm
M2×6mm
Power Socket Mount
2
M3×6mm
M3×8mm
Fan
4
use nuts
M3×12mm
Speakers
8
M3×6mm
M3×8mm
Rear Panel
4
M3×6mm
M3×6mm
Stand Leg
2
M3×6mm
M3×12mm
Power Supply Mount
2
M3×6mm
M3×6mm
Raspberry Pi is a trademark of Raspberry Pi Ltd.
PERSONAL SYSTEM/2 (TM) is a trademark of IBM, August 4, 1987.
Print spec
- Formats
- stlstpzip
- Model files
- 56
- Total size
- 10.5 MB
- Largest file
- 1.8 MB
0 comments
You may also like 12 models
See all-

-
New -

-

-

-

-

-

-

-
New -

-



