Skip to main content
F3D
LoRa Meshcore / Meshtastic Solar Repeater / Node 196mm 1

20 images

DIY

LoRa Meshcore / Meshtastic Solar Repeater / Node 196mm

By massive

Downloads
147

Files 10 3.9 MB

  • 196 COVER 1ANT V4 SCREWS.stlSTL · 119 KB
  • 196 COVER BRIDGE V4 SCREWS.stlSTL · 119 KB
  • 196 BOX 1ANT V5 SCREWS.stlSTL · 1.4 MB
  • Miktronik 868 Antenna Support.stlSTL · 40.3 KB

Make a variant with AI

Build another version of this model.

Open Studio

Description

Cover works on all box versions.

UPDATE: 2026-07-29: Added Bridge Support Upper V2

UPDATE: 2026-07-25: Added Bridge 196 V6 and bridge support lower and upper for 2X T114 and 3065.
UPDATE: 2026-05-08: Added Bridge (double antenna for two separate networks ie. 868-433 on the same box)
UPDATE: 2026-06-10: Added V5. Small changes, nothing structural. 
Added support for Mikrotik 868 Antennas. 
 

Instructions for your LoRa Solar Station:

Print:

Need at least a buildplate of 200mm. This box has 196mm.

With supports only touching the buildplate. Supports only necessary on the screws and nuts.

Print with HIGH infill density on a filament that can take the rain and heat. Example: PETG, ASA, etc etc.

Back to the buildplate on the box.

Front to the buildplate on the cover.

Has space for 4x, 3x, 2x, 1x 18650 batteries.

This case was designed with the following components in mind:

4mm silicone gasket: https://www.amazon.es/-/pt/dp/B0CWND3XN7

5x - M6 x 30mm screws (and nuts).

PG7 cable connector: https://www.amazon.es/-/pt/dp/B07JH2LPZF

N Female connector 10cm or 5cm: https://pt.aliexpress.com/item/1005008877279360.html

U bolts this size: https://pt.aliexpress.com/item/1005005032237148.html or https://pt.aliexpress.com/item/1005007643403270.html

Mounting Pole (if you don't have one): https://pt.aliexpress.com/item/1005009921117319.html

Designed for this solar panel: https://www.amazon.es/-/pt/dp/B0D6NMFZ5C

Antenna of this type: (433): https://pt.aliexpress.com/item/1005007301219597.html

(868 or 915): https://pt.aliexpress.com/item/1005007301116616.html

Might help to have an extra gasket for the female connector/antenna and the interior solar panel screw: https://www.amazon.es/-/pt/dp/B09KGPLVJ7

Dimensions and specs:

196mm x 149mm x 60mm

Weight: Around 500grs.

Solar panel tilt: 64º (optimized for the winter sunlight in Lisbon, Portugal ~38.7°N)

Box has thick walls to withstand the weather.

Has two vents to help with heat and condensation.

A series of ideas to stop the rain: silicone gasket, outer wall, screws all outside (except one for the solar panel).

It's plastic so don't go crazy torquing when holding it to the pole.

Example setup for LifePO4 (DOUBLE CHECK EVERYTHING)

1S 3.2V BMS - https://pt.aliexpress.com/item/1005010481169075.html

1S TP5000 3.6V - https://pt.aliexpress.com/item/1005009339731648.html

1S PARALLEL HOLDER: https://pt.aliexpress.com/item/1005001955162216.html

Disclaimer:

Use at your own risk! Always read before you act! I am not an expert!

LoRa networks might save your life and others.

TQMaxcielle3D, LX-Portugal

Read more Show less

Print spec

Formats
stl
Model files
10
Total size
3.9 MB
Largest file
1.4 MB

0 comments

See all