
Airnode – Nút cảm biến giám sát chất lượng không khí
Remix of Mảng Cảm Biến Khí Thải Máy In 3D (Sensorbox v2) By MadeWithLayers
- Downloads
- 1
- Likes
- 0
- Views
- 58
- Remixes
- 0
- Comments
- 0
Files 8 4.8 MB
- case_1778676529.stlSTL · 2.5 MB
- carrier_sen55_1778676531.stlSTL · 107.1 KB
- screen_bracket_right_1778676532.stlSTL · 72.5 KB
- screen_bracket_left_1778676533.stlSTL · 72.5 KB
Make a variant with AI
Build another version of this model.
Details
- Model ID
- #383763
- Category
- DIY
- Published
Description
Airnode
A Professional-Grade, Edge-Intelligent Air Quality Monitoring Node
The Elevator Pitch
From the moment I saw Tom's air sensor, I wanted to build one. Along the way, I found some room for improvement in the design. A full PCB and firmware redesign later here we are.
Most DIY sensors dump raw data to the cloud and hope for the best. Airnode is designed like a commercial IoT product: it fuses 9+ sensor modalities into a real-time environmental intelligence platform that computes, calibrates, and visualizes everything on-device. An air flow chamber for the sensors with a fan that gently draws air over the sensors. Built on a custom ESP32-S2 PCB with a production-ready color GUI, it demonstrates end-to-end embedded systems skills: analog signal conditioning, sensor fusion, statistical calibration, fault-tolerant architecture, and polished human-machine interface design.
What Makes It Special
Capability
Why It Matters
Autonomous Gas Calibration Engine
MOS gas sensors drift over time. Airnode runs a finite-state machine that detects clean-air baselines using CO₂, VOC, PM₂.₅, and HCHO cross-references, then statistically validates stability (CV < 5 %) before auto-updating calibration constants.
Temperature & Humidity Compensation
All raw gas resistance values are corrected against live T/RH references before AQI calculation, eliminating seasonal skew.
Multi-Modal AQI at the Edge
Instead of exposing confusing raw voltages, Airnode computes EPA-style AQI scales (0–500) for three gas domains and surfaces a Composite AQI (worst-case wins) so you never miss a hazard.
Fault-Tolerant Architecture
A 1-minute health watchdog monitors sensor validity. If critical channels fail for >5 minutes, the device auto-reboots to recover bus communication.
Five-Screen Color Dashboard
A responsive 240×320 IPS Screen. Utilitarian UI with contextual color coding (green → red), brightness control, and hardware button navigation.
Production IoT Stack
Offline first. Native ESPHome: captive portal, web server, and instant Home Assistant integration, if desired.
Sensor Payload
Parameter
Sensor
Notes
PM₁ / PM₂.₅ / PM₄ / PM₁₀
Sensirion SEN55
Laser scattering + VOC & NOₓ indices
CO₂
Sensirion SCD40
Photoacoustic NDIR, self-calibrating
Formaldehyde
Sensirion SFA30
ppb-level HCHO detection
VOCs / Odor
Figaro TGS2602
MOS broad-range organics
Solvents / Ethanol
Figaro TGS2620
MOS alcohol & vapor sensitivity
Reducing Gases (CO, H₂, NH₃)
MiCS-5524
MOS reducing gas detector
Temp / Humidity
Sensirion SH3X/SH4x
Reference for compensation algorithms
Pressure
Bosch BMP280
Barometric
System Health
Fan tachometer
PWM fan RPM monitoring
The Auto-Calibration Engine ( Deep Dive)
The hardest problem in gas sensing is baseline drift. Airnode solves this with a custom C++ lambda state machine:
-
Clean Air Gate — Every minute, the system verifies that:
-
CO₂ < 450 ppm
-
VOC index < 120
-
PM₂.₅ < 5 µg/m³
-
HCHO < 30 ppb
-
-
Stability Analysis — When air is clean, Rs values are accumulated. After 5+ minutes, the Coefficient of Variation (CV) is computed.
-
Guarded Update — Only if CV < 5 % is the
Robaseline updated via an exponential moving average (70 % new / 30 % old), bounded by physical sensor limits to prevent runaway. -
Manual Override — A hardware button trigger forces the same validation pipeline, or resets accumulators for a fresh start.
Display & UX Flow
A 2.4" ILI9341 TFT renders five contextual screens:
-
Screen 0: Overview — At-a-glance grid of Temp, Humidity, Pressure, CO₂, VOC, HCHO, PM1/2.5/10 with live color-coded thresholds.
-
Screen 1: Gas AQI Detail — Composite AQI bar, individual sensor AQIs, estimated PPM for CO, VOC, and Ethanol, and live Rs/Ro ratios.
-
Screen 2: Calibration — State machine status (warmup / clean-air countdown / last cal time), current Ro constants, and live Rs values.
-
Screen 3: Quick Guide — On-device reference for interpreting AQI scales and comfort ranges.
-
Screen 4: System Status — WiFi SSID/IP/signal, ESPHome version, MAC, uptime, free heap, and fan RPM.
Hardware Controls
-
Button 1 (Short Press): Cycle 6 PWM backlight levels (100 % → 12 %).
-
Button 1 (Long Press): Toggle backlight on/off.
-
Button 2: Cycle through the five screens.
-
Navigation Dots: Bottom-of-screen indicators show active page.
BOM / Instructions coming soon
Print spec
- Formats
- stltxtzip
- Model files
- 8
- Total size
- 4.8 MB
- Largest file
- 2.5 MB
0 comments
You may also like 12 models
See all-
New -
New -

-

-

-

-
New -

-

-

-
New -
New

