
Ốp lưng semi-closed cho tai nghe Satyr3
Remix of Satyr 3 (Tai nghe HiFi DIY) By CapraAudio
- Downloads
- 0
- Likes
- 0
- Views
- 66
- Remixes
- 0
- Comments
- 0
Files 5 22.5 MB
- Cover_1778119030.3mf3MF · 141.7 KB
- Cover_1778119031.stlSTL · 433 KB
- Cover_1778119031.f3dF3D · 598.3 KB
- Cover_0.4n_0.2mm_PETG_COREONE_5h29m_1778119033.bgcodeBGCODE · 10.9 MB
Make a variant with AI
Build another version of this model.
Details
- Model ID
- #374934
- Category
- Dụng Cụ Tiện Ích
- Published
Description
The Satyr3 is an open-back headphone, and as such leakes quite some noise into your surroundings. This remix converts it to a semi-closed headphone by replacing the fascia by a vented dome, so you feel comfortable wearing it in public. This strikes a balance between sound leakage and audio quality.
Disclaimer:
-
This modification affects the sound quality of your Satyr3. You lose some of the low basses but treble leakage is reduced by ~50%.
-
I'm neither an audio engineer nor an audiophile. I stopped iterating once it leaked sufficiently less sound but still sounded almost the same to the original (to my untrained ear):
-
1st iteration: Fully closed back (facepalm) --> dead bass
-
2nd iteration: This model --> still too much leakage
-
3rd and final iteration: This model + Dekoni foam
-
-
My understanding of how headphone geometry and airflows affect sound quality is negligible and strictly less than ChatGPT's. Here's the full conversation in which it suggested this design.
- No AI was involved in creating the actual 3D model.
Printing
It's a pretty straightforward print, but using variable layer height is recommended to reduce visible layer lines.
Print settings:
-
Nozzle: 0.4mm (HF)
-
Layer height: 0.2mm, but use variable layer height on top of dome (see .mf3 file)
-
Material: PETG (recommended) or PLA
-
Supports: Optional, only at the dome apex, do not touch vents or insert holes
The cover is symmetric, you need 2 pieces per headphone.
Materials
You need the same heatset inserts used for the original fascia of the Satyr3 headphones.
BoM:
- 4x M3 heatset inserts, 3mm (recommended) to 4mm (max) long and 4.5-5mm diameter.
Assembly
The cover replaces the Satyr3 fascia. Hence,
-
Place 2x M3 heatset inserts into each dome.
-
Glue some Dekoni foam to the interior of the dome.
-
1-2mm layer of low to medium density foam that cover the vent holes
-
4-6mm layer of medium density foam in the center
-
Do NOT line entire dome with foam (see picture, do not use more than that)
-
Vary density/layer height to fine-tune the leakage vs. sound quality trade-off to your preference.
-
Start with empty dome
-
Add Dekoni foam until
-
sound leakage was sufficiently reduced, or
-
sound quality deteriorates to unacceptable levels
-
-
-
-
Follow the Satyr3 instructions on how to install the fascia
Print spec
- Formats
- 3mfbgcodef3dstl
- Model files
- 5
- Total size
- 22.5 MB
- Largest file
- 10.9 MB
0 comments
You may also like 12 models
See all-
New -

-

-

-
New -

-
New -
New -
New -
New -

-


