Skip to main content
F3D
Extrudr Spool Filament Clip v2 + CSDL Trọng Lượng 1

1 image

Máy In 3D

Extrudr Spool Filament Clip v2 + CSDL Trọng Lượng

By xro42

Downloads
33
Likes
4
Views
400
Remixes
1

Files 10 3 MB

  • extrudr_filament_clip_v2-PrusaSlicer_1777680093.3mf3MF · 204.6 KB
  • extrudr_filament_clip_v2-BambuStudio_1777680095.3mf3MF · 250.6 KB
  • extrudr_filament_clip_v2_-_S_Type_C_single_hole_1777680095.objOBJ · 234.3 KB
  • extrudr_filament_clip_v2_-_SM_Type_AB_single_hole_1777680097.objOBJ · 243.9 KB

Make a variant with AI

Build another version of this model.

Open Studio

Remix versions 1

See all 1 remix

Description

An inline filament clip for Extrudr spools.

Well … several actually, as Extrudr uses a bunch of different spools.

The clip weighs 1.06g and the filament can be clipped-in/removed without removing the clip.

The clip can remain inside the spool.

As the Extrudr-Spools have only one spot with 2-holes, I have added a version that will clip into a single hole. It may not stay straight, but maybe that's ok with you.

Spool Variants

Image

Name

Look

Prevalence

Empty Spool Weight

Hole Distance

S/M - Type A

800g to 1100g

outer ring has straight lines 

inner ring more straight lines

very common

244g

21 mm

S - Type B

800g to 1100g

outer ring has flat diamonds

inner ring has reverse diamonds

medium common

259g

21 mm

S - Type C

800g

outer ring has bulging fat diamonds

inner ring trapezoids

older and uncommon

275g

29mm

S/M - Type D

1000g

straight lines and circles radiating from center

I have 1 of those

255g

22¼mm

Seeking for your input! / Help required

I'm looking for measurements of any Extrudr spool I have not yet encountered.

e.g.:

  • 2kg L spool

  • 5kg XL spool

  • 10kg XXL spool

If you have a version of those, please drop me a message with the following measurements:

  • use caliper, measure inner distance between two holes

  • use caliper, measure diameter of a hole, or several to get an average

  • width of spool plastic wall, where the hole is

Printing

  • 100% infill

  • print nipple up - lay flat on face with filament recess

  • recommend layer height between 0.20mm to 0.40mm

  • good with 0.6mm nozzle but everything else works too

  • no supports

  • with smooth printbed, edges of filament recess will melt a bit inward, holding the filament even better. You might have to thread it in and not be able to push it in from the side.

  • with textured printbed, there is no inward melting, you can push the filament in from the side.

Updates

Update 2025-03-17

  • tighter bend, smaller diameter, higher clip, so filament will hold even better.

  • added 1-hole version

Update 2025-03-18

  • a comment by @newyen_359607 made me re-check ALL my Extrudr spools, where I discovered that at least one differs quite a bit.

Update 2025-03-25

  • discovered yet another unique Extrudr 1kg spool

Credits:

Inspired by many other great clips of this sort.

Read more Show less

Print spec

Formats
3mfbgcodefcstdobj
Model files
10
Total size
3 MB
Largest file
686.2 KB

0 comments

See all