
Cánh máy bay RC in 3D VELORA [Bản test piece]
- Downloads
- 625
- Likes
- 78
- Views
- 5,026
- Remixes
- 0
- Comments
- 0
Files 2 1.9 MB
- FUSELAGE_1_NOSE_CONE_1777452411.3mf3MF · 980.6 KB
- Left_Wing_1.gcode_1777452412.3mf3MF · 964.2 KB
Make a variant with AI
Build another version of this model.
Details
- Model ID
- #351326
- Category
- DIY
- Published
Description
FINAL VERSION LINK
Link to build plate adhesive that I use for reliable printing:
PLEASE LEAVE A COMMENT IF YOU HAVE A QUESTION OR IDEA FOR IMPROVEMENT.
NOTES
CG is marked on bottom of plane with an inset circle. In my experience, this CG location requires a tiny bit of up elevator to fly level. Feedback from first tester indicates that this CG is a neutral position and they preferred a slightly more forward CG. I will leave it as is.
MOTOR MOUNT has been updated for 16mm spacing drone motors.
SPECS
- Wingspan: 820mm
- Weight:~1kg
- Length: 540mm
HARDWARE
- Magnets:
- 4 * 8mmx3mm magnets for hatches
- Screws:
- 2 * M3 x 12 - 16mm screws for holding in the motor mount
- 8 * M2 Screws for holding in the servo hatch
- Filament:
- TPU for hinges
- PLA+ [~600g]
- Motor: T-Motor F80 PRO 2200kv
- ESC: 40 amp
- Propeller: 6 x 4
- Battery: 4S
- Flight Controller [not required]: Speedybee f405 mini with gps or equivalent
- Servos: 9g servos [SG90] NOTE: I have heard people commonly use EMAX ES08 servos and will look into the dimensions to add alternate mounting for those.
Printing Settings:
!!Use brim for all larger parts, lifting up even a small amount will create parts that are hard to combine cleanly!!
!!Zhop is highly recommended for tall parts to decrease the likelihood of knocking them over!!
- Starting Point for Settings:
- 0.4mm wall with 1 perimeter
- 3 layers, top and bottom
- 0.25mm layer height
- 0% infill
- Additional Part Specific Settings:
- For WING 1
- You will need support for the top of the servo tray area, I recommend Hybrid Tree Supports.
- For Tail Fin and Tail Fin Mount:
- Increase to 2 perimeters
- For Wing Tip:
- Change to 0.16mm layer height, to allow for curvature
- For Fuselage 3 and 4:
- Add 6% gyroid infill with 0mm to 2mm Maximum Length of Sparse Infill Anchor (lowers weight)
- For Motor Mount:
- Change to 4 perimeters minimum and 15% infill minimum. Possible to use PETG here for increased heat resistance.
- For Servo Covers:
- Increase to 3 perimeters and 10% infill.
- Control Horns:
- Increase to 4 perimeters and 100% infill
- Change to 0.16mm layer height
- For Body Spar Support:
- 4 perimeters and 20% infill
- For Spar:
- 6 perimeters and 15% infill
- For Hinges:
- Print using TPU settings 100%infill, probably just a few layers thick
- For Connectors:
- Print out of PLA with 100% infill [same file as hinges]
- For WING 1
Print spec
- Formats
- 3mf
- Model files
- 2
- Total size
- 1.9 MB
- Largest file
- 980.6 KB
0 comments
You may also like 12 models
See all-

-

-

-

-
New -

-

-

-

-

-
New -

![Cánh máy bay RC in 3D VELORA [Bản test piece] 1](https://cdn.f3d-ai.com/uploads/public/69f/1b6/ac1/69f1b6ac16bda148505925.png?class=w1600)
![Cánh máy bay RC in 3D VELORA [Bản test piece] 2](https://cdn.f3d-ai.com/uploads/public/69f/1b6/aca/69f1b6aca33b0731161880.png?class=w1600)