TF2 Hitman's Heatmaker (Bản mod Nerf từ Sillybutts Foxbat)

You need the original Foxbat kit, plus the following:

https://docs.google.com/spreadsheets/d/1KOiNNJb-DsYRX4Xing8HacSmP-WwXPeXNfO9-ASy6mA/edit?usp=sharing

Assembly guide:

1. Assemble the bolt like the original Foxbat. (M3X16 qty 2, M3X30 qty 1)

2.  Assemble CatchHolder and PlungerGuide with qty 3 #4 screws. Add the Catch with two small springs from the kit. Cover with CatchHolderPlate using qty 2 #4 screws

3. Assemble the FrontBlock_NoSights piece plus the StraightTalon_TriggerBar, TriggerYoke, and CatchPusher,  using the two small pins, M3 square nut and 10mm screw, and the Clevis Pin, like the original Foxbat.

4. Add in the plunger tube and main spring,  the BackBlock, and the small spring in between for trigger return 

5. Add the Trigger Joint piece with qty4 #4 screws. Add the Turnaround with all the orings like how the original Foxbat was assembled (Dash123 O-ring qty 2 and Dash016 O-ring qty 2)

6.  Assembled the barrel and the BarrelCover piece using qty2 M3 30mm screws

7. Add the  Trigger extend piece with qty 4 #4 screws

8.  Assemble both sides of the rare furniture, using qty 4 on both sides, indicated locations, 8 total

9. Assemble the Trigger with qty 1 #4 screw, plus the StraightTalon_GripBottom_Shorter_HH from the back, secure both sides with qty 4 #4 screws

10.  Add Center Joint piece in the green location, qty 2 ball detent in blue locations, and qty 2 #4 screws in red locations

11. Install StraightTalon_GripTop and DartGuide, using qty 2 #4 screws each

12. Attached SlideBack_NoIronSightsto the CatchHolder with qty 5 #4 screws. Install the RAM with qty 4 #4 screws

12. Add the front bit of the grip furniture using qty 5 #4 screw on both sides

13.  Assemble the trigger guard section with the Aft and Front Linkage, the StraightTalon_GripBottom_Shorter_HH, and the Outerlinks. Secure with qty 4 #4 screws each on both sides in the purple locations. And secure with qty 1 M4x25mm screw and nut to link the grip with the Front Linkage

14. Cover the grip with Side Pannel_R &L on both sides, secure with qty 4 #4 screws

15. Install the Fake Barrel_Front v2 with qty 6 #4 screws

16. Add Fake Barrel_Back with qty 2 #4 screws, assemble onto the Bolt core the following parts: Bolt cover with qty 4 #4 screws, Bolt with qty 1 M4x70mm screw and nut, StockRing with qty 2 #4 screws

17. Add Stock_slideV2 with qty 4 #4 screws

18. Assemble the stock using qty 14 M4x45mm screws and nuts

19. Install the Cheak rest, StoclButt, and Stock_Joint using qty 10 #4 screws

20. Install the Scope bracket 1 &2 using qty 8 #4 screws

21. Assemble the RangeFinder as the image shows; cut a section of filament and place it in the red location to keep the parts aligned. Secure the parts with qty 3 #4 screws

22. Install the range finder and the falke decal screws with qty 4 #4 screws

23. Install the Supressor parts, safety tip, and parts for the scope (needs glue in between) with qty 6 #4 screws