Skip to main content
F3D
Giá đỡ tai nghe PlayStation PS5 (Cao 30cm) 1

11 images

Dụng Cụ Tiện Ích

Giá đỡ tai nghe PlayStation PS5 (Cao 30cm)

By mysak85

Downloads
147
Likes
30
Views
1,529

Files 11 6.2 MB

  • part7.black_1773432327.stlSTL · 93.2 KB
  • part1.black_1773432329.stlSTL · 210.4 KB
  • part3.white_1773432330.stlSTL · 369.8 KB
  • part9.black.white.logo_1773432331.stlSTL · 172.5 KB

Make a variant with AI

Build another version of this model.

Open Studio

Description

V případě, že se Vám výtisk povede, prosím přidejte fotografii. DĚKUJI

If the printout is successful for you, please add a photo. THANK YOU

Aktualizace 15.01.2023

Je přidána možnost stojánku na DualSense, zde se tisknou 

part2.black.s.dualsense a dualsense.holder

Výška celého stojanu je 30 cm

Celý stojan jsem tisknul s tryskou 0.6 až na logo, to bylo vytištěno tryskou 0.25
Použil jsem šrouby M4x18 a čtvercové matky.
Díly je nutné k sobě ještě slepit aby to celé drželo pohromadě.
Tisknuto skoro celé bez podpěr, podpěry jsou nutné jen tam, kde jsou otvory na čtvercové matky a na díl 07 který je dobré tisknout na výšku.

Díly 08 a 09 jsou tisknuty dvojbarevně tak, aby co nejlépe ladily s konzolí Plastation 5.
Použil jsem PETG bílou a černou.

Na vrchní díl kde jsou zavěšená sluchátka jsem použil tejpovací pásku , ale je dobré použít cokoliv měkkého nebo gumového aby nedocházelo k oděru sluchátek.

V případě že někdo bude tisknout, tak poprosím o komentář jestli bylo vše v pořádku, případně co třeba zlepšit.

A kdyby mně chtěl někdo podpořit v dalším vytváření nových věcí, tak je možnost přes Revolut.

Děkuji

English:

Update 01/15/2023

The option of a stand on the DualSense is added, they are printed here

part2.black.s.dualsense and dualsense.holder

The height of the entire stand is 30 cm
I printed the entire stand with a 0.6 nozzle, except for the logo, which was printed with a 0.25 nozzle
I used M4x18 screws and square nuts.
The parts still need to be glued together to hold the whole thing together.
Printed almost completely without supports, supports are only necessary where there are holes for square nuts and for part 07 which is good to print in portrait.

Parts 08 and 09 are printed in two colors to best match the Plastation 5 console.
I used PETG white and black.

I used duct tape on the top part where the headphones are hung, but it's good to use anything soft or rubbery to prevent the headphones from rubbing.

In the event that someone will print, I will ask for a comment on whether everything was fine or what needs to be improved.

And if someone wants to support me in the further creation of new things, there is an option through Revolut.

Thank you

Read more Show less

Print spec

Formats
stl
Model files
11
Total size
6.2 MB
Largest file
2.2 MB

0 comments

See all