Skip to main content
F3D
Giá đỡ điện thoại Fallout Pip-boy Mk IV kèm Stand 1

7 images

Dụng Cụ Tiện Ích

Giá đỡ điện thoại Fallout Pip-boy Mk IV kèm Stand

Remix of Kẹp thẻ Pip-Boy 3000 Mk IV (Pip-Boy 3000 Mk IV Badge Holder) By TSpawn_25165

By G0OSE

Downloads
7
Likes
8
Views
290

Files 13 2.2 MB

  • BODYV4_1771222820.stlSTL · 1.1 MB
  • bezel_1771222821.stlSTL · 348.3 KB
  • back_1771222822.stlSTL · 170.5 KB
  • large_knob_1771222823.stlSTL · 130.7 KB

Make a variant with AI

Build another version of this model.

Open Studio

Description

I dearly wanted a real proper pip boy, and though I could afford it it was still a lot of money for what at then end of the day would ultimately be an expensive desk ornament, mostly used as a clock and radio player.

So....I decided to make exactly that, but this doesn't fit on your wrist, and it's not expensive. I didn't want the hassle of printing an entire pip boy, so this fits the bill perfectly.

I used T-Spawn's fantastic pip boy badge holder and went to work editing it so it would fit an old android phone which I had laying around, in this case it's an HTC One M8, but any phone that measures less than 147 x 71 x 9.7mm will fit - all you'd have to do if it was smaller is pack it out with something, maybe foam (in my honest opinion this is so cool it warrants buying an old phone for if you don't have one!) Alternatively, import the body into tinkercad or alike and ajust the phone cut out size. The black knobs both turn, but don't do anything - just glue the pins in to hold in place.

I printed it in Sunlu pla+ and as always did adaptive layer heigh to 0.3 and smoothed abut 7 times in Orca slicer. Make sure your printer is dialed in for the filament you are using or things may not fit as they should.

The magnets I used were 10 x 8mm x 0.9mm (that may have been sold as 1mm) but 0.9 is what they measure. You glue one of each into the back part, making sure the holes are clear of any debris etc and pushed in hard and flat, then what I did was put the other 5 mangets on top and put double sisded tape on the top, the holes in the back are deep enough to accomodate both magnets - you then simply snap it together and the 2nd magnets will be stuck to the pip boy body, you could superglue the 2nd mangets, but you run the risk of glueing the model together if not careful!!

The gasket fits between the body and bezel. I did this in black. If you don't have a phone that fits, you could always print out some screenshots of a pip boy display from the web and put those inside. I have also included some cutouts for the guages which you can either leave blank or stick some images to from the web with all the details on.

The pip boy simply rests on the stand provided which push fits together and looks really cool.

This is my best design yet, I am so happy with it - again massive thanks to T-Spawn for the original design, I couldn't have done it without that as a start point.

The apps I use on it are very old, but are still available  but not from the Play store any more.

Be AWARE as these apps are not on the Play store and are from 3rd party sites, you install them at your own risk.

Bethesda Pip-boy app is still available (HERE) and so far as I know it still actualy works with Fallout 4

Pipdroid is also still available (HERE), and better still plays your music - if you download this one, rename the file to .zip, then extract it - otherwise it'l ask you to install some installer which you don't need (pureapk)

To install the .apk's you'll need to enable 'install from other sources' in your settings, again do this at your own risk. Simply click on them and they will install - both of those apps allow you to resize the screen and orient it to you liking.

Read more Show less

Print spec

Formats
stl
Model files
13
Total size
2.2 MB
Largest file
1.1 MB

0 comments

See all