Skip to main content
F3D
Creality Dry Box 2.0 Bowden Tube Strain Relief v2 (PC4-M10) 1

18 images

Máy In 3D

Creality Dry Box 2.0 Bowden Tube Strain Relief v2 (PC4-M10)

Remix of Chống gập ống Bowden cho Creality Dry Box 2.0 (Strain Relief) By DamianNowak

By Alpha_Eps_2518160

Downloads
5
Views
92

Files 2 436.4 KB

  • Creality_Dry_Box_2.0_Bowden_Tube_Strain_Relief_Remix_1767397748.stlSTL · 276.2 KB
  • Creality_Dry_Box_2.0_Bowden_Tube_Strain_Relief_Remix_1767397748.3mf3MF · 160.2 KB

Make a variant with AI

Build another version of this model.

Open Studio

Description

This is a REMIX of Damian Nowak's Creality Dry Box 2.0 Bowden Tube Strain Relief model. 

 I bought the Creality Dry Box 2.0 so that I could keep TPU dry while printing with my P1S. The box has a small port on the rear of the lid to allow filament to exit, however, the port accepts PTFE perpendicular to the spool and not tangent to it. From an engineering design perspective, the drier is well made but the exit angle of the filament must be adjusted for improved performance. 

 I searched Makerworld, Thingiverse, Thanks, and Printables for an answer to my problem. Surely someone has found this issue too. I printed many different models; Mr. Nowak's model was the closest to what I needed. In fact, it has quite a few benefits:

  • The angle of the PTFE tube is tangent to the internal spool,

  • The model hugs the outside of the lid closely,

  • Uses screws for a tight mechanical fit,

  • Can be oriented horizontally or vertically,

  • Included a template for careful modification of the Creality Dry Box 2.0,

  • The box modification can be “reversed” since the OE rubber stopper will cover the holes in the lid. 

However, there were two issues: 

  1. The M3 hex nuts did not fit into the model's slots. This is noted in several comments for this model. 

  2. Mr. Nowak suggests that the PC4-M6 allows the PTFE tube to passthrough into the dry box. However, all of my PC4-M6 connectors DO NOT allow the PTFE tube through. Unless I have unusual connectors, something needed to change.

I needed to make a few changes. 1) I enlarged the slots for the M3 nuts. 2) I enlarged the PTFE orifice to allow a PC4-M10 connector to be inserted. I included the templates made by Mr. Nowak in this print. The directions below were written by Mr. Nowak with a few edits by myself. 

 I printed my model in PLA and PETG. I expect that ABS could also be used, but it has not been tried as of this date 2025-12-27.

  1. Screw PTFE tube PC4-M10 adapter in the printed part. My adapters fit halfway before requiring a few turns with a wrench. I got 2-4 full turns of thread engagement. Although not necessary, you could use an M10 x 1.0 tap to cut threads. I did not find this necessary.

  2. Drill two 3mm holes in the drybox lid using  an included drill template.

    1. You can still pop the rubber adapter back if not happy with this mod. 

    2. There are two templates: 

      1. One with M4 Nuts to be used a drill guides. If you intend to modify multiple dry boxes, then using nuts will make this template reusable. I did not use this template, but have included it here.

      2. One without M4 Nuts. This is the template that I used since I was only modifying one dry box.

  3. Insert in two M3 nuts into the printed part

  4. Use two M3 x 20mm screws to attach it

  5. Slide the tube in - I suggest pushing so it reaches halfway into the dry box for best results.

Read more Show less

Print spec

Formats
3mfstl
Model files
2
Total size
436.4 KB
Largest file
276.2 KB

0 comments

See all