
Điều Khiển Quạt Tự Động Cho Bento Box
Remix of Bộ lọc carbon BentoBox v2.0 cho máy in Bambu Lab X1C By thrutheframe
- Downloads
- 150
- Likes
- 65
- Views
- 2,872
- Remixes
- 0
- Comments
- 0
Files 4 64.5 MB
- FanDuct_1766374321.stlSTL · 62.6 MB
- Electronics_Housing_1766374324.stepSTEP · 1.1 MB
- VOC_CKT_Program_1766374328.zipZIP · 5.7 KB
- pico-pinout_1766374329.svgSVG · 738.2 KB
Make a variant with AI
Build another version of this model.
Details
- Model ID
- #128801
- Category
- Máy In 3D
- Published
Description
For the latest revisions, please visit: https://github.com/gallowayk/FanControlForBentoBox
After printing out the Bento Box filtration model, I wanted a means to control the fans so they weren't on 24/7 and only enabled when high VOC content was present. Originally, I was only going to use a bimetal temp switch since the ambient internal temperature of the printer would only rise while printing ABS, PC, Nylon, etc. However, I wanted to take a more sophisticated approach while keeping costs low.
- RPi Pico (any variant)
- 3.3V trigger opto-isolated relay https://www.amazon.com/dp/B07XGZSYJV
- MS1100 gas sensor https://www.amazon.com/dp/B0BF4JDW26
- 128x64px SSD1306 OLED screen https://www.amazon.com/gp/product/B0833PF7ML
- LM2596S buck converter https://www.amazon.com/gp/product/B07QKHR6PY
- The buck converter must be adjusted to +5VDC or +3/3.3VDC
Hardware
- 2x M2x5 or M2x8 self-tapping screw
- One for VOC sensor
- One for RPi Pico
- 8x 4x2mm Magnets
- Various jumper wires
- Helps to use male to female jumper wires
- It also helps to have a Dupont connection/terminal kit and crimper; this will allow you to make your own wires of just the right length
Tools
- Soldering iron
- TS100 is my go-to due to its rapid heating and cooling
- "Helping hands" for soldering
- Precision tool set
- Ball-end hex keys can be used as well
- Ferrule crimper + ferrules
- Heatshrink
Note: Please be sure to safely work on your electronics.
- Do not work on anything while power is connected
- Do your best to avoid inhaling the flux/solder fumes
Software
Please read through the entire program to acclimate yourself with the functionality!
Pin definitions can be easily changed at the top from those I chose to use.
- For those who haven't used Raspberry Pis for their own scripts, rename “VOC_CKT.py” to “main.py” and save to your RPi Pico.
When I have a bit more time, I'll create a full write up with instructions on how to connect everything. Until then, feel free to ask me questions. Please note, however, that I may not be able to respond quickly.
There are still some tweaks I'd like to make, so a revision may come at some point. I want to reduce the clutter in the electronics housing by utilizing integrated solutions or developing my own PCB with an RP2040 chip and on-board power handling.
Print spec
- Formats
- stepstlsvgzip
- Model files
- 4
- Total size
- 64.5 MB
- Largest file
- 62.6 MB
0 comments
You may also like 12 models
See all-

-

-

-
New -
New -

-

-
New -

-

-

-


