Skip to main content
F3D
Poker Chips (Single Color) 单色扑克筹码 1

5 images

Board Game

Poker Chips (Single Color) 单色扑克筹码

By Boski_1345590

Downloads
104
Likes
6
Views
337

Files 5 680.2 KB

  • Poker_Chips_Single_Color_-_1_1777714017.stlSTL · 114.2 KB
  • Poker_Chips_Single_Color_-_5_1777714018.stlSTL · 127.8 KB
  • Poker_Chips_Single_Color_-_10_1777714019.stlSTL · 134.2 KB
  • Poker_Chips_Single_Color_-_25_1777714019.stlSTL · 149.9 KB

Make a variant with AI

Build another version of this model.

Open Studio

Details

Model ID
#364441
Category
Board Game
Published

Description

Translated by Chat-GPT

This is a simple and easy-to-print poker chip designed with a single color, so there’s no need to change colors during printing.

Since it’s a single color, I used other methods to simulate the white Edge Spots typically seen on poker chips. I ultimately opted for engraved lines instead of raising or lowering the height of the Edge Spots. The purpose of this design is to give the chip a cleaner look while maintaining a consistent height when viewed from the side. The engraved grooves also help retain a good level of distinguishability when the chips are stacked.

Given the small size, there is no need to add chamfers.

It is generally recommended to print using standard chip colors: 1, 5, 10, 25, and 100 correspond to white, red, blue, green, and black, respectively. The suggested print quantities are in a ratio of 4:3:2:2:1. Of course, you can decide on the color and quantity of each denomination based on your own preference.

The chip dimensions are 40mm × 2mm. You can scale them according to your preference, but I cannot guarantee the visibility of details if the size is reduced.

The recommended layer height for printing is 0.2mm. It is also suggested to enable top surface ironing for a smoother and finer appearance.

---

中文描述

这是一款简单易打印的扑克筹码,采用单一颜色设计,所以打印时无需更换颜色。

由于是单色,所以采用了其他方法来模拟筹码上白色的 Edge Spots。我最终选择了雕刻线条,而不是整体抬升或降低 Edge Spots 部分的高度。这样做的目的是使筹码外观更简洁,并且从侧面看上去能够保持一致的高度,同时雕刻的凹槽让筹码在堆叠时也不会丢失太多的可辨性。

由于体积很小,所以没有必要设计倒角。

通常情况下建议使用标准筹码颜色打印,1、5、10、25、100 分别对应白色、红色、蓝色、绿色、黑色。打印数量建议 4:3:2:2:1。当然,你也可以根据自己的喜好来决定每种面值筹码的颜色和数量。

筹码的尺寸是 40mm × 2mm,你也可以按照自己的喜好来缩放打印,但是如果缩小尺寸,我不保证细节的可辨性。

打印层高建议 0.2mm。建议添加顶面熨烫,以获得更加平滑细腻的外观。

Read more Show less

Print spec

Formats
stl
Model files
5
Total size
680.2 KB
Largest file
154.1 KB

0 comments

See all