Skip to main content
F3D
Eyeglass Case Mk4 (Hộp đựng kính không cần support) 1

1 image

Trang Phục - Phụ Kiện

Eyeglass Case Mk4 (Hộp đựng kính không cần support)

By pueckler_3167359

Downloads
12
Likes
6
Views
145

Files 4 13.2 MB

  • Seitenwand_separatMK4_1774374994.3mf3MF · 115.9 KB
  • EyeglassCase6mmMk4a_1774374994.3mf3MF · 391.3 KB
  • Seitenwand_separatMK4_0.4n_0.15mm_PETG_COREONE_4h4m_1774374995.bgcodeBGCODE · 6.6 MB
  • EyeglassCase-MK4_0.4n_0.15mm_ASA_COREONE_4h12m_1774374997.bgcodeBGCODE · 6.1 MB

Make a variant with AI

Build another version of this model.

Open Studio

Details

Model ID
#261519
Published

Description

Die Idee dieses Entwurfs ist ein Brillenetui, bei dem die Brille nicht auf ihren Gläsern liegt und zerkratzt, sondern an den Bügeln fixiert wird. Allerdings funktioniert diese Version nur mit Brillen, deren Bügelscharniere am oberen Rand der Gläser liegen und deren Bügel eher schmal sind, am besten nicht viel stärker als 6mm. (Eine Version mit austauschbaren Brillenhaltern gibt es auch.)

Das Brillenetui besteht aus einem Hauptkörper mit Bodenplatte und Deckel sowie einer Seitenwand, die nach dem Druck an der Bodenplatte eingefügt und mit Sekundenkleber fixiert wird. Für die Stabilität der Scharniere sorgt während des Drucks eine dünne Opferschicht, die nach dem Druck gebrochen werden muss, indem man das Etui vorsichtig öffnet. (Eventuell kann es beim ersten Mal sinnvoll sein, den Deckel am Verschluss mit einem 5-Cent-Stück vorsichtig aufzuhebeln und ihn dann schrittweise weiter zu öffnen, bis die Opferschicht gebrochen ist.)

Das Etui kann komplett ohne Support und ohne Rand vertikal auf dem Druckbett gedruckt werden. Bei mir hat das mit PETG und ASA sehr gut funktioniert; bei manchen PLA-Filamenten war das Brechen der Opferschicht an den Scharnieren schwierig. (Im Foto: grün = Extrudr BioFusion PLA, Orange = 3dJake Easy PETG, grau = eSun PLA)

_______________

The idea behind this design is a glasses case in which the glasses do not rest on their lenses and get scratched, but are secured by their arms. However, this version only works with glasses whose arm hinges are positioned at the top edge of the lenses and whose arms are relatively narrow – ideally no more than 6 mm wide. (A version with interchangeable glasses holders is also available.)

The glasses case consists of a main body with a base plate and lid, as well as a side panel which is inserted into the base plate after printing and secured with superglue. During printing, a thin sacrificial layer ensures the stability of the hinges; this must be broken after printing by carefully opening the case. (It may be helpful the first time to carefully pry the lid open at the clasp using a 5-pence coin and then gradually open it further until the sacrificial layer has broken.)

The case can be printed vertically on the print bed without any supports or overhangs. This worked very well for me with PETG and ASA; with some PLA filaments, breaking the sacrificial layer at the hinges proved difficult.

Read more Show less

Print spec

Formats
3mfbgcode
Model files
4
Total size
13.2 MB
Largest file
6.6 MB

0 comments

See all