
Ender 3 Pro Beefy Y (dây đai 9mm/motor 60mm/double shear)
- Downloads
- 3
- Likes
- 1
- Views
- 79
- Remixes
- 0
- Comments
- 0
Files 8 20 MB
- Motor_mount_1772157860.stlSTL · 471.9 KB
- Idler_right_1772157861.stlSTL · 342.5 KB
- Idler_left_1772157862.stlSTL · 309.3 KB
- Spacer_1772157863.stlSTL · 107.5 KB
Make a variant with AI
Build another version of this model.
Details
- Model ID
- #228631
- Category
- Máy In 3D
- Published
Description
This is a mod for the Ender 3 Pro (and probably also V2) to improve Y axis performance using:
-
9mm GT2 belt
-
Longer stepper – up to 60mm
-
Double-shear bearing to support the stepper motor shaft (optional)
BOM and assembly notes:
-
16T GT2 pulleys, 9mm (x2)
-
One for the motor; the side with the screws should be oriented away from the motor body.
-
One for the idler
-
-
625-2RS bearings (x3)
-
Two for the idler
-
One for double shear support on the motor (theoretically optional, but you won't be able to take full advantage of the 9mm belt without it).
-
-
M5x30mm dowel pin
- For the idler
-
M5x0.5mm shim
- On the pin, between the pulley and bearing
-
M5x20mm countersunk screw
- On the front of the idler
-
9mm GT2 belt (approximately 1m)
-
M5x10mm BHCS or SHCS screws (x8)
- To mount the parts to the Y axis 4040 extrusion; longer screws would also work
-
M5 nut
- Trapped inside the tensioner
-
M3x8 BHCS or SHCS screws (x2)
- On the sides of the tensioner (use washers)
-
M3x35mm BSCS or SHCS screws (x7)
-
3 on the tensioner
-
4 on the motor mount (use washers if your screws bottom out before they're fully tightened against the plastic part)
-
-
M3 washers (x2 or more)
-
M3x5mm heat-set inserts (x5)
- All 5 go on the tensioner
-
M4x14mm SHCS or BHCS screws
- For the sensorless homing "endstop" (optional)
-
M4 T-slot nuts (x2)
- For the sensorless homing "endstop" (optional)
-
NEMA17 stepper motor
-
An approximately 21mm or longer shaft is required for double shear support
-
I'm using this one because I already had it around, but other options might be more suitable: https://www.amazon.com/dp/B00QGBUO1C
-
Notes:
-
I printed my parts using ABS/ASA-GF/CF, 7 perimeters but only 15% infill.
-
All parts can be printed without supports
-
A 6mm belt could also be used with additional spacers on the tensioner and motor shaft, but the stock belt will not be long enough
-
The stock Y endstop will not work. I included here an "endstop" that can be installed on the Y axis extrusion towards the back for sensorless homing. If you prefer, you could also design a holder to mount a traditional microswitch endstop.
-
For reference, I'm getting around 5k input shaper recommended acceleration, but with the belt at only 140Hz over 15cm.
-
I'm using the following belt clamps:
Print spec
- Formats
- f3dstepstl
- Model files
- 8
- Total size
- 20 MB
- Largest file
- 12 MB
0 comments
You may also like 12 models
See all-

-

-

-

-
New -
New -

-
New -
New -

-

-


