Skip to main content
F3D
| ATLA | Nhà Chữa Bệnh Của Bắc Hải 1

9 images

Thế Giới - Mẫu Scan 3D

| ATLA | Nhà Chữa Bệnh Của Bắc Hải

By Sedak

Downloads
45
Likes
8
Views
454

Files 15 138.2 MB

  • NWTHH_one_piece_1765561265.stlSTL · 73.4 MB
  • NWTHH_roof_1765490013.stlSTL · 13.9 MB
  • NWTHH_walls_and_floor_1765490166.stlSTL · 9 MB
  • NWTHH_base_1_1765490261.stlSTL · 7.6 MB

Make a variant with AI

Build another version of this model.

Open Studio

Description

| BASIC DESCRIPTION |

  • this is a scaled model of a healing hut from the northern tribe in animated series Avatar: The Last Airbender
  • it was modeld using the scenes from the episode “The Waterbending Master”
  • interior and exterior of the hut are modeled
  • it still has some parts that I would like to improve and repair in time (like some proportions that are not quite right)

Scene with the huts:

| DESIGN DECISIONS |

  • I used the people in scenes as a reference
  • the model was scaled to 1:60 scale so it can fit nicely on a standard 3D printing bed when printed in parts
  • parts snap together, but I would still use glue for the base tiles - the roof can stay unglued so that you can remove it and explore the interior of the hut
  • the model is sliced in a way that removes the need for most of the support
  • in the files there is also a 3D model of the whole hut in one piece if you want to print it that way - just make sure to use support for the roof
  • the ornaments on the inside of the walls are depicting the lunar phases. It is not perfectly aligned as it is shown in series, but it has some logic behind it - as there are 8 lunar phases, and 11 fields depicting it I thought that the most logical arrangement was so that the phases are on the sides, and the center position on the wall is always a standard water tribe emblem
  • so in the end i modeled 3 water tribe emblems and one entrence forming a cross while around them on the sides there are moon phases (8 of them)
  • on the bottom base there is an Avatar logo from the show

Interior of the hut:

| PRINT SETTINGS |

  • it depends on the part you are printing and the quality you want to achieve
  • do not forget the supports for the small part of the lifted roof on the entrance, also I added some supports for the entrance itself - you can print withouth them, but the model won't look as nice.
  • all the parts are orineted correctly for FDM 3D printing
  • I have added my own 3mf files so you can see all the settings there

| OTHER ATLA MODELS |

| ATLA | Sokka's club:

https://www.printables.com/model/662969-atla-sokkas-club

| ATLA | Avatar Kyoshi's headdress:

https://www.printables.com/model/659114-atla-avatar-kyoshis-headdress

| ATLA | Earth Rumble Battle Arena Icon:

https://www.printables.com/model/741641-atla-earth-rumble-battle-arena-icon

| ASSEMBLY |

  • I have to buy some new light blue fillament and then I will print out the model in full so that I can make the assembly guide - comming soon
  • for now, on the picture here is only a test model that I have printed in one piece (with organic supports):

Read more Show less

Print spec

Formats
3mfstl
Model files
15
Total size
138.2 MB
Largest file
73.4 MB

0 comments

See all