{"slice":{"locale":"en","from":20000,"to":28128,"total_chars":28128,"html":"<p>hing that was re-purposed :)</p>\n<p>Information on the BC-250: <a href=\"https://github.com/mothenjoyer69/bc250-documentation\" rel=\"nofollow ugc noopener\" target=\"_blank\">https://github.com/mothenjoyer69/bc250-documentation</a> </p>\n<p>Basic Specs:</p>\n<p>CPU = 6 x Zen 2 Cores with SMT</p>\n<p>GPU = 24 RDNA 2 CU’s</p>\n<p>Ram = 16GB of GDDR6 Shared Between System and GPU, very much like the Steam Deck and others like the Lenovo Legond Go with the Z1 Extreme (8 CPU Cores and 12 RDNA CU’s)</p>\n<p>So this makes it a very nice little performer for the money, its like a Steam Deck APU on steroids, or another way to look at it, its 1080/1440p version of the Steam Deck APU, and will handle any Game that runs under Linux at 1080P Medium to High Settings at over 60fps.</p>\n<p>Also do not skimp out on the fan, use the ones I have linked to and full tested in my design, avoid the standard Arctic P12, it lacks the performance required, you will want the P12 Pro or the P12 Max, if you use some other fan, well, your results may vary.</p>\n<p>After many weeks of thermal testing, bench marking and testing designs, fan types and fan orientation, I found the blowing into the case using a static pressure booster and a strong fan like the P12 Pro CO from Arctic was the best choice and has resulted in a machine that can be fully overclocked and has the capacity to easily dissipate 350w of power.</p>\n<p>The cooling system on this open source game console, uses the exact same principles as the Steam Deck, and the upcoming Steam Machine, the entire system is cooled with a single fan, pulling air in through the bottom of the case, and over all of the hot parts, then venting out the top, I have taken inspiration from the team at valve, and I have designed this in a way, that makes it hard to block inlet, and outlet venting, you would need to wrap it in clingwrap like some sort of <a href=\"https://en.wikipedia.org/wiki/Bad_Boy_Bubby\" rel=\"nofollow ugc noopener\" target=\"_blank\">Bad Boy Bubby</a> freak to “choke out” the cooling system :)</p>\n<p>I highly recommend printing from anything other than PLA, please avoid this terrible material, and print from, at a minimum, PETG, preferably PETG with Glass Fibre or Carbon Fibre, as it will make a substantially better looking device, glossy looking coloured plastic looks tacky, and the layer lines show due to reflecting light, matte finished material looks considerably better, specially if you plan on showcasing this in your living room, and for me, it has passed WAF (For the younger folks, that's &quot;Wife Approval Factor&quot;) and this can be quite important in some households.</p>\n<p>I have printed mine in the following materials:</p>\n<p>Fan Mount:</p>\n<p>Upper and Lower Gaskets = TPU</p>\n<p>Mount Mount: PC-CF</p>\n<p>Casing:</p>\n<p>Front in dual colour: PETG-CF and Logos done in Matte White PETG-GF</p>\n<p>Rear: PETG-CF</p>\n<p>Hex Mesh Trims and Optional Vertical Stand:</p>\n<p>All done in: Matte White PETG-GF</p>\n<p>Feet:</p>\n<p>Printed 4 of these in: White TPU</p>\n<p>The Fan mount might be okay in PETG-GF or CF, but I would recommend ABS at a minimum as the heat sink can get fairly hot if you have the fan running at a lower speed.</p>\n<p>All of the threaded inserts can be installed without any heat, just fit them like a nut on the inside and use the socket head M3 bolt to pull them into the seat I have modelled into the casing, very simple and easy, if you have big chunky hands like me it can be a little fiddly on the rear part of the case, but if I can do it, then I think almost anyone can do it.</p>\n<p>I’m currently putting together a video on assembling this, and I will have additional videos showing how to install and setup Bazzite, then a bunch of videos showing benchmarks and gaming performance on many Steam titles.</p>\n<p>At the moment, you will need a 300mm x 300mm Bed to print this, but in the coming days I will upload a modified version that will print on a 220mm x 220mm Bed, along with version that you can screw into the plastic instead of nice threaded inserts, and a special request in the Discord for a version to take a 38mm 10k Rpm Server fan.</p>\n<p>Some photos of the finished product, this is in the horizontal position:</p>\n<p>This is in the vertical position with the optional vertical stand:</p>\n<p>Here is a shot in its natural habitat:</p>\n<p>Latest benchmarks for the BC-250 running in my case under Bazzite:</p>\n<p>Link to my Bazzite forum thread: <a href=\"https://universal-blue.discourse.group/t/i-just-created-the-bazzite-box-low-cost-steam-machine/11182/6\" rel=\"nofollow ugc noopener\" target=\"_blank\">https://universal-blue.discourse.group/t/i-just-created-the-bazzite-box-low-cost-steam-machine/11182/6</a></p>\n<p>Printing Orientation:</p>\n<ul>\n<li>Fan mount and static pressure booster</li>\n</ul>\n<ul>\n<li>300mm3 or larger beds</li>\n</ul>\n<ul>\n<li>220mm3 beds</li>\n</ul>\n<p><strong>This are is where I will post images and guides on how to do certain things:</strong></p>\n<p>How to install the threaded inserts:</p>\n<p>Opening up the cooler, my recommendation is to use a pair of scissors, just mid sized ones will do, the trip is to be patient, and no rush it, you are not cutting, but its more like peeling, the folded part is quite weak, so once it starts peeling it comes away quite easily, the trick, is to do it from the IO side of the board all the way across, this is due to the way the blade is profiled on scissors and the way the finstack top is folded over, please see the following photos;</p>\n<p>As you can see, I use a piece of plastic to support a bladed and the other peels the top away, you just work you way across, from the IO side of the board to the other, one at a time, you can use a small cutting board as a brace or some wood, I decided to use the vertical stand for the case :)</p>\n<p>As you can see here, it looks extremely neat and tidy, much better than trying to bend them in or out.</p>\n<p>Wiring diagram for the latching Press Button Switch:</p>\n<p>In some cases the NO/C/NC wiring colours can vary, so just check on the back of the switch itself as its inscribed on there, so just check before connecting.</p>\n<ul>\n<li>\n<p>Switch Wire Code:</p>\n</li>\n<li>\n<p>Green = Common (C) - Goes to Ground on the 24 Pin Plug</p>\n</li>\n<li>\n<p>Blue = Normally Open (NO) - Goes to the PS_ON on the 24 Pin Plug.</p>\n</li>\n<li>\n<p>Yellow = Normally Closed (NC) - This is not used</p>\n</li>\n<li>\n<p>Red = 12v - Power for the LED Ring - Red goes to 12v on the 24 Pin Plug.</p>\n</li>\n<li>\n<p>Black - Ground - Power for the LED Ring - Goes to Ground on the 24 Pin Plug</p>\n</li>\n</ul>\n<p><strong>Wiring Into The 24 Pin Plug:</strong></p>\n<p>Easiest way to do this is to just tap in, solder and tape with some electrical tape, if you cant solder, then just twist and tape.</p>\n<p>My recommend insulation tap is this awesome PET based tape from Tesa: <a href=\"https://amzn.to/458K5XM\" rel=\"nofollow ugc noopener\" target=\"_blank\">Flame Retardant PET 51036 Tape</a></p>\n<p>Below images show the easiest way to strip and tap in</p>\n<p><strong>Preparing the Board:</strong></p>\n<p>You must remove the IO Shield and small mounting bracket before install the board in the case, as these are not required.</p>\n<p>Removing the Heatsink:</p>\n<p>If you want to replace the TIM, I highly recommend PTM7950 and <a href=\"https://amzn.to/4sxVoTd\" rel=\"nofollow ugc noopener\" target=\"_blank\">Thermal Putty</a> for the VRAM Modules, along with new <a href=\"https://amzn.to/49epR1a\" rel=\"nofollow ugc noopener\" target=\"_blank\">2mm Thick Pads</a> for the VRM's, there is just 8 simple screws to remove, the centre 4 are the ones that clamp the heat sink down to the APU, and the 4 outer ones clamp the the heatsink down to the VRM's and secure the back plate:</p>\n<p>And it should look like this once done:</p>\n<p>Pin out details for the FSP500-30AS Power Supply:</p>\n<p>Stay tuned for more images.......</p>\n<p>If you would like to ask me question or discuss the project, please feel free to make contact with me on the Bazzite forum: <a href=\"https://universal-blue.discourse.group/t/i-just-created-the-bazzite-box-low-cost-steam-machine/11182/12\" rel=\"nofollow ugc noopener\" target=\"_blank\">Bazzite Forum Post</a></p>","has_more":false},"deferred":false}
